Aalborg TIO Totalizer I/O Flow Monitor/Controller Bedienungsanleitung Seite 12
- Seite / 98
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
8
Table 4.2 Maximum rated load impedance for SP output signals
SP
OUTPUT
TYPE
J2 JUMPER
CONFIGURATION
MAXIMUM
LOAD
IMPEDANCE
NOTE
J2A J2B J2C
0 - 5 Vdc 2 - 3 5 - 6 8 - 9
≤1000 Ohm
0 - 10 Vdc 2 - 3 5 - 6 8 - 9
≤5000 Ohm
Special Order option! (PCB
hardware must be changed).
4 – 20 mA 1 - 2 4 - 5 7 - 8
≤900 Ohm
(24 Vdc PS)
Self-powered (non-isolated)
current loop. For 12 Vdc PS
the load impedance should not
exceed 400 Ohm.
CAUTION: When connecting the load to the output terminals always
check actual jumper J2 configuration. Do not exceed the rated values
shown in the specifications (see Table 4.2). Failure to do so might
cause damage to this device. Be sure to check if the wiring and the
polarity of the power supply and SP signals are correct before
turning the power ON. Wiring error may cause damage or faulty
operation. Do not connect external voltage source to the SP
output terminals.
PV output (+) --------------- pin 5 of the 9 pin "D" connector
PV output (-) --------------- pin 8 of the 9 pin "D" connector
WARNING: The 4-20 mA current loop output is self-powered (non-
isolated). Do not connect an external voltage source to the output
signals.
4.4 Digital Communication Interface Connections
The digital interface operates via RS-232 (optional RS-485) and provides access
to all applicable internal configuration parameters and data.
Communication Settings for RS-232/RS-485 communication interface:
Baud rate: default 9600 baud (user-selectable. See specification section).
Stop bit: .................... 1
Data bits: .................... 8
Parity: .................... None
Flow Control: .................... None
- OPERATING MANUAL 1
- TABLE OF CONTENTS 3
- Fw: A002 Tbl: A001 17
- Interface: RS-232 17
- Baud Rate: 9600 17
- RS485 address: 11 17
- A:D litr/min 18
- T1: 1589324.5 litr 18
- S: 100.0 litr/min 18
- T1: 1589324.5 litr 18
- Events Reg: No Events 19
- PO:E U/P: 1.000 litr 19
- DO# 1: Pulse Output 19
- DO# 2: Disabled 19
- 51.01 litr/min 21
- S 51.0 0.0s 21
- CS: 1 0.0 0 21
- M:D L:Off S: Off 21
- Figure 5.7 24
- TIO Upper Levels 24
- Menu Structure 24
- Screen Masc: 38
- Screen #2 [*] 38
- Screen #3 [*] 38
- Screen #4 [*] 38
- Screen #1 [*] 38
- “Controller” 39
- ENT button to 42
- No Active Events 49
- Press any key 51
- PO Queue: 0 52
- Max Limit: 250 52
- Assemblies 63
- Generic Flow Controller 69
- 7.2 Troubleshooting Guide 72
- APPENDIX A 74
- Rev.A001 [08/10/2011] 74
- INDEX NAME DATA TYPE NOTES 75
- APPENDIX B 79
- Internal K-Factors Table 79
- Process Screens Mask 91
- APPENDIX D 95
- Mechanical Drawings 95
- APPENDIX E 96
- Circuit Layout Diagrams 96
- Circuit Layout Top 96
- Circuit Layout Bottom 97
- CAUTION: 98
Verwandte Produkte und Handbücher für Relais Aalborg TIO Totalizer I/O Flow Monitor/Controller
Relais Aalborg Vortex Bedienungsanleitung
(117 Seiten)
(117 Seiten)
Relais Aalborg Vortex Insertion Bedienungsanleitung
(123 Seiten)
(123 Seiten)
Lumastream Step Light Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Beleuchtung Lumastream Step Light.
Wir stellen 1 PDF-Handbücher Lumastream Step Light zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Kommentare zu diesen Handbüchern