Aalborg AFC Bedienungsanleitung Seite 7
- Seite / 36
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Important Notes:
In general, "D" Connector numbering patterns are standardized. There are, how-
ever, some connectors with nonconforming patterns and the numbering sequence
on your mating connector may or may not coincide with the numbering sequence
shown in our pin configuration table above. It is imperative that you match the
appropriate wires in accordance with the correct sequence regardless of the par-
ticular numbers displayed on your mating connector.
Make sure power is OFF when connecting or disconnecting any cables in the system.
The (+) and (-) power inputs are each protected by a 750mA M (medium time-lag)
resettable fuse. If a shorting condition or polarity reversal occurs, the fuse will cut
power to the flow transducer circuit. Disconnect the power to the unit, remove the
faulty condition, and reconnect the power. The fuse will reset once the faulty con-
dition has been removed.
Cable length may not exceed 9.5 feet (3 meters).
Use of the AFM/AFC flow transducer in a manner other than that specified in this
manual or in writing from Aalborg7, may impair the protection provided by the
equipment.
3. PRINCIPLE OF OPERATION
The stream of gas entering the Mass Flow transducer is split by shunting a small
portion of the flow through a capillary stainless steel sensor tube. The remainder of
the gas flows through the primary flow conduit. The geometry of the primary
conduit and the sensor tube are designed to ensure laminar flow in each branch.
According to principles of fluid dynamics the flow rates of a gas in the two laminar
flow conduits are proportional to one another. Therefore, the flow rates measured in
the sensor tube are directly proportional to the total flow through the transducer.
In order to sense the flow in the sensor tube, heat flux is introduced at two sec-
tions of the sensor tube by means of precision wound heater-sensor coils. Heat is
transferred through the thin wall of the sensor tube to the gas flowing inside. As
gas flow takes place heat is carried by the gas stream from the upstream coil to
the downstream coil windings. The resultant temperature dependent resistance
differential is detected by the electronic control circuit. The measured gradient at
the sensor windings is linearly proportional to the instantaneous rate of flow tak-
ing place.
An output signal is generated that is a function of the amount of heat carried by
the gases to indicate mass-molecular based flow rates.
Additionally, AFC model Mass Flow Controllers incorporate a proportionating
solenoid valve. The closed loop control circuit of the AFC continuously compares
the mass flow output with the selected flow rate. Deviations from the set point are
corrected by compensating valve adjustments, thus maintaining the desired flow
parameters.
4
Verwandte Produkte und Handbücher für Relais Aalborg AFC
Relais Aalborg I/O-485 Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Relais Aalborg XFM Digital Bedienungsanleitung
(56 Seiten)
(56 Seiten)
Relais Aalborg Totalizer Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Relais Aalborg PWE Digital Bedienungsanleitung
(83 Seiten)
(83 Seiten)
Relais Aalborg TIO Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Relais Aalborg OSS-2 Optical Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Relais Aalborg Vortex Bedienungsanleitung
(117 Seiten)
(117 Seiten)
Relais Aalborg Vortex Insertion Bedienungsanleitung
(123 Seiten)
(123 Seiten)
Philips 8718696482445 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Taśmy LED Philips 8718696482445.
Dostarczamy 1 pdf podręczników Philips 8718696482445 do pobrania za darmo według typów dokumentów: Arkusz Danych
Kommentare zu diesen Handbüchern